10/04/2022 | Jerry Mackelburg | The repaired automatic blast gate was reinstalled and tested. | Table Saw 10 Inch #2 Sawstop Professional | 1,099 |
10/04/2022 | Rick VanHatten | Changed the paper | Drum Sander 16 Inch Jet | 1,098 |
10/03/2022 | Paul Schankin | Sandpaper on drum beginning to tear. Please replace. | Drum Sander 16 Inch Jet | 1,097 |
10/03/2022 | Paul Schankin | Please order replacement fuses for Oneida. Order (2) sets of two each fuses for total of 4 as Oneida requires 3 fuses be replaced at same time. Link: https://www.amazon.com/Bussman-FRN-R-30-Volt-Delay-Count/dp/B00V53NI0A/ref=asc_df_B00V53NI0A/?tag=hyprod-20&linkCode=df0&hvadid=193994910693&hvpos=&hvnetw=g&hvrand=16256410621196189997&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9061190&hvtargid=pla-312322313983&psc=1 | Dust Collector 7.5 HP Oneida | 1,096 |
10/03/2022 | Dallas Keck | Tools leads for the 3D printer now include Jenna Roessel and Chris MuTools MuLab License key. This log entry is to test that they are receiving email notifications from Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021 log. | 3D Printer | 1,095 |
10/02/2022 | Paul Schankin | Per report #1091 Removed black filament clog in hot end. Ran cleaning filament through extruder 3X to clear residue. Ran multiple Z calibration tests, reset Z cal to -0.965 height. Ran test print with white filament, 3D printer returned to service. | 3D Printer | 1,094 |
10/01/2022 | Jerry Mackelburg | The automatic blast gate has been temporarily returned to manual operation. I piece of wood in the ductwork had apparently prevented the automated gate's slider from fully closing – which likely broke the microsoft office 365 product key 2018 Activators Patch acrylic carriage adapter. The slider remaining in the nearly closed position, in addition to long thin strips of wood in the saw's internal ductwork, probably caused that ductwork to get clogged. Since the clog consisted mostly of wood savings, the saw blade was replaced with an obviously re-sharpened one (with protective wax). | Table Saw 10 Inch #2 Sawstop Professional | 1,093 |
10/01/2022 | Dana Chapin | Changed blade | Band Saw 14 Inch Laguna SE | 1,092 |
10/01/2022 | Dallas Keck | The black filament is jammed in the extruder. | 3D Printer | 1,091 |
09/28/2022 | Doug Murphy | Had a situation today where where two members wanted to use the rotary fixture for the laser. First come first serve. We might want to consider making this a reservation item. | Not a Tool Repair Issue | 1,090 |
09/18/2022 | Jerry Mackelburg | The power supply for the blast gate is mounted above the Oneida's rightmost collection drum. That power ytd video downloader full version is plugged in via an DataDynamics ActiveReports ActiveX License key cord to an AC outlet near the Shapeoko XXL, Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021. It was unplugged, so Dallas plugged it in to restore operation. | Drum Sander 25 Inch Supermax | 1,089 |
09/18/2022 | Jerry Mackelburg | Cleaned cutters/cutterhead. Cleaned and waxed tables and table rollers. | Planer 20 Inch General International | 1,088 |
09/18/2022 | Jerry Mackelburg | Cleaned cutters/cutterhead and cleaned and waxed tables. | Jointer 12 Inch Grizzly | 1,087 |
09/18/2022 | Paul Schankin | Clog removed. | 3D Printer | 1,086 |
09/17/2022 | Duane Kuperus | Check Drum/feed table for parallel. Seems lower on drive sire. | Drum Sander 16 Inch Jet | 1,085 |
09/16/2022 | Mark Umphres | The auto gate opener is not working | Drum Sander 25 Inch Supermax | 1,084 |
09/13/2022 | Jerry Mackelburg | I broke Dallas' automated blast gate today – so the gate is back to manual operation until it gets fixed. | Planer 13 inch Dewalt | 1,083 |
09/13/2022 | Patrick Duffy | There was a report of no connectivity between the Nova 51 and its computer. Resolution: Reseated the ethernet cable. TOK. | Laser Thunder Nova 51 | 1,082 |
09/12/2022 | Jerry Mackelburg | One of the 30A fuses blew on startup during Sunday's Intro Class – it was replaced. The other two were replaced today since they only seem to last about two years. (All three were replaced autodesk 3ds max 2019 system requirements two years ago.) The two good but aged fuses that were removed were appropriately labeled and placed in the upper dust collector parts drawer in the current bench room cabinet. | Dust Collector 7.5 HP Oneida | 1,081 |
09/12/2022 | Jerry Mackelburg | It appears that the sanding belt is either too fine, worn out, defective, mislabeled, or some combination thereof – see report #1,073. | Edge Sander N/A Grizzly | 1,080 |
09/12/2022 | Travis Good | Communication between computer and laser isn't working. | Laser Thunder Nova 51 | 1,079 |
09/12/2022 | Jerry Mackelburg | Some users find both the switches on the automatic blast gate controllers and the electronics/linear actuator mounted near SawStop wolfram mathematica 11.2 crack blast gate confusing. SawStop #1's blast gate slider was replaced with one that can't be pulled out when the gate is opened. | Dust Collector 7.5 HP Oneida | 1,078 |
09/08/2022 | Jerry Mackelburg | Dallas installed his prototype automated blast gate. | Planer 13 inch Dewalt | 1,077 |
09/08/2022 | Jerry Mackelburg | Added a motor power monitor to the top of the power switch housing. | Planer 20 Inch General International | 1,076 |
09/08/2022 | Jerry Mackelburg | Moved the plywood sheets that were blocking the fans on the left side of the laser. | Laser Thunder Nova 51 | 1,075 |
09/08/2022 | Jerry Mackelburg | Pat cleaned the rust off the cast iron top, waxed it, and adjusted the Incra router lift's base plate height adjustment setscrews. | Router Table #2 Rockler | 1,074 |
09/05/2022 | Bryan Blacksher | The edge belt sander is not sanding hardly at all even with very firm pressure. I don't know if it is just the belt or something else. Tried various heights on the belt but that did not help much. | Edge Sander N/A Grizzly | 1,073 |
09/04/2022 | Dana Chapin | Replaced handle on fence | Band Saw 16 Inch Deep freeze standard 8.37 + crack Chapin | Changed blade | Band Saw 14 Inch Laguna 3000 | 1,071 |
09/03/2022 | Jerry Mackelburg | Dallas replaced the broken blade. | Band Saw 14 Inch Laguna SE | 1,070 |
09/03/2022 | Jerry Mackelburg | Cast iron top router table. Cleaned and dry sprayed lubed leadscrew and guides to provide smoother lift operation. Top is rusting badly – it should probably be cleaned up and waxed before it gets much worse. | Router Table #2 Rockler | 1,069 |
09/03/2022 | Jerry Mackelburg | Phenolic top router table. Cleaned and dry sprayed lubed leadscrew and guides to provide smoother operation. | Router Table #1 Rockler/INCRA | 1,068 |
09/03/2022 | Oi Ling Kwan | saw blade boke while being used | Band Saw 14 Inch Laguna SE | 1,067 |
09/02/2022 | Paul Schankin | Printer clogged. Ordered filament cleaner for 3D. ETR (estimated time for repair) is Sept 20. 3D printer out of service. | 3D Printer | 1,066 |
08/30/2022 | Duane Kuperus | Disassembled saw blade elevation gear and lock. Removed elevation control shaft and replaced worn lock key. Reassembled and greased/cleaned parts. Suggest that Jixipix Premium Pack Free Download knobs no longer be used at all for both elevation and tilt wheels. At the very least we should instruct all operators to make sure the lock knobs are loose prior to positioning (elevation/tilt) the blade. I spoke to SawStop tech support and they said that using the locks really does not help. The key was worn due to operation of the elevation handwheel with lock knob tightened. Not the correct operation. | Table Saw 10 Inch #1 Sawstop Industrial | 1,065 |
08/30/2022 | Paul Schankin | Rapaired jammed mirror/lens head. Nova 51 in service. | Laser Thunder Nova 51 | 1,064 |
08/29/2022 | Tom York | The fence adjustment lever is broken, I think. The threads have been stripped or broken, so that lever doesn't work properly. | Band Saw 16 Inch Laguna | 1,063 |
08/29/2022 | Paul Schankin | User reports workpiece and Z bed driven up into focus block. Nova 51 out of service. | Laser Thunder Nova 51 | 1,062 |
08/22/2022 | Paul Schankin | Cleared filament wrapped around in feed roller. Ran test 3D print job, job successful. 3D printer in service. | 3D Printer | 1,061 |
08/22/2022 | Paul Schankin | Filament wrapped around feed roller. 3D printer out of service. | 3D Printer | 1,060 |
08/22/2022 | Paul Schankin | Replaced dust collection bag. 80% full | Shop Vac Rigid | 1,059 |
08/20/2022 | Nancy Bosecker | The sandpaper on the belt portion of the combo sander has shifted off center. I'm not sure how to fix it so logging it here. The sander is still operational. | Disk/Belt Sander Jet | 1,058 |
08/13/2022 | Paul Duffield | The blade height lock is not working/stripped thread? | Table Saw 10 Inch #1 Sawstop Industrial | 1,057 |
08/13/2022 | Paul Duffield | The whole saw is vibrating when running and the emergency brake seems to operate when the regular stop button is pressed. The wheels feels like the brake is on all the time, even when the power is off. | Band Saw 14 Inch Laguna 3000 | 1,056 |
08/13/2022 | Duane Kuperus | Shop is slow today. Did preventative maintenance on the #1 saw. Clean internals and lube. | Table Saw 10 Inch #1 Sawstop Industrial | 1,055 |
08/12/2022 | Paul Duffield | I was able to change the belt | Drum Sander 25 Inch Supermax | 1,054 |
08/12/2022 | Paul Duffield | Sanding belt is gummed up. Did not have time to change the belt. | Drum Sander 25 Inch Supermax | 1,053 |
08/10/2022 | Jerry Mackelburg | The router in the cast iron router table was dropping when rounding sapele edges during yesterday's Introduction to Woodworking class. The lift manual (https://incra.com/manuals/MastRLiftII_Manual.pdf) says “If the bit height ever begins to change (or drop) during use, the thread tensioning likely needs to be reset.” | Router Table #2 Rockler | 1,052 |
08/08/2022 | Paul Schankin | Dust collection bag replaced, 85% full. Last bag replaced Nov 2021. | Dust Extractor Bosch | 1,051 |
08/08/2022 | Paul Schankin | Shop chisels are reported to need sharpening | Not a Tool Repair Issue | 1,050 |
08/05/2022 | Paul Schankin | Nozzle and hot end clogged with black Adaware Antivirus Crack. Replaced PTFE tube during disassembly/assembly and verified operational after clearing nozzle. 3D printer in service. | 3D Printer | 1,049 |
08/05/2022 | Mary Russo | Really needs to have the sandpaper disk replaced. | Disk/Belt Sander Jet | 1,048 |
08/05/2022 | Paul Schankin | Report of clogged print nozzle. 3D printer out of service. | 3D Printer | 1,047 |
08/04/2022 | Paul Schankin | Reference report 1045. Loss of DC power to blast gate controller due to AC power plug for power supply contacted by CNC gantry during movement. Relocated AC plug to different AC receptacle to prevent interference with CNC gantry moves. Blast gate controller now powered on. | Drum Sander antares license free Inch Supermax | 1,046 |
08/03/2022 | Ron Prater | Vacuum blast gate is always open. I think the contoller isn't powered. | Drum Sander 25 Inch Supermax | 1,045 |
08/02/2022 | Jerry Mackelburg | One of the 1/8″ chippers in the Freud Super Dado stack was discarded because one of its four carbide cutters was missing. | Not a Tool Repair Issue | 1,044 |
07/31/2022 | Patrick Duffy | Carbide 3d software upgrade: Carbide Create now Build 652; Carbide Motion now Build 566. | CNC Shapeco 32 inches square | 1,043 |
07/31/2022 | Patrick Duffy | Carbide 3d software upgrade: Carbide Create now Build 652; Carbide Motion now Build 566. | CNC Shapeco 32 inches square | 1,042 |
07/30/2022 | Jerry Mackelburg | The Bridge City Tri Squares were adjusted. The un-adjustable machinists' squares that weren't square were removed from the tool wall. The most accurate combination squares that could be found in the shop were placed on the tool wall. The combination squares in the education toolbox aren't too bad either. The Bridge City Miter Squares seemed accurate in a quicky test, so they weren't adjusted (it's not clear that they can be anyway.) | Hand Tools | 1,041 |
07/30/2022 | Patrick Duffy | The laser is not cutting a vertical line into material. The result is that butted joints may not fully join across the joining surfaces. | Laser Thunder Nova 35 | 1,040 |
07/30/2022 | Patrick Duffy | The laser focus tube mount was loose. Adjusted the concentric bearing adjustment plates on the X gantry. Three of the four set screws were loose. Thanks to David Collins who brought it to my attention. | Laser Thunder Nova 35 | 1,039 |
07/27/2022 | Dana Chapin | Replaced tires | Band Saw 14 Inch Laguna 3000 | 1,038 |
07/27/2022 | Dana Chapin | Replaced blade | Band Saw 14 Inch Laguna 3000 | 1,037 |
07/27/2022 | Dana Chapin | Replaced blade | Band Saw 14 Inch Laguna SE | 1,036 |
07/23/2022 | Jerry Mackelburg | The 0-degree miter detent was adjusted to minimize error when using the left easeus data recovery wizard 12.9 crack download to make 90-degree cuts. | Miter Saw 12 Inch Bosch | 1,035 |
07/21/2022 | Jerry Mackelburg | July 19 – The Miter Detent System probably needs to be adjusted. | Miter Saw 12 Inch Bosch | 1,034 |
07/21/2022 | Jerry Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021 19 – The largest Bridge City “Try Square” needs to be adjusted. | Hand Tools | 1,033 |
07/20/2022 | Jerry Mackelburg | ? | Not a Tool Repair Issue | 1,032 |
07/20/2022 | Jim McGihon | Coding test | Test Tool | 1,031 |
07/20/2022 | Jim McGihon | Coding test | Test Tool | 1,030 |
07/20/2022 | Jerry Mackelburg | Test | Not a Tool Repair Issue | 1,029 |
07/20/2022 | Jerry Mackelburg | The “Miter Detent System” and “Miter Scale Pointer” probably need to be adjusted. | Miter Saw 12 Inch Bosch | 1,028 |
07/20/2022 | Jerry Mackelburg | The large (and other?) Bridge City “Try square” needs to be adjusted, Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021. | Hand Tools | 1,027 |
07/20/2022 | Paul Schankin | Revised PC login to standard user, password remains the same. Made new Admin user for restricting apps being loaded on PC. PC in service. | Laser Thunder Nova 51 | 1,026 |
07/20/2022 | Paul Schankin | Revised PC login to standard user, password remains the same. Made new Admin user for restricting apps being loaded on PC. PC in service. | Laser Thunder Nova 35 | 1,025 |
07/19/2022 | Wesly Berneberg | One of the random orbital sanders vibrates too much and makes some noise while being used. The sander is on the front bench in the bench room. | Hand Tools | 1,024 |
07/19/2022 | Paul Schankin | another test | Laser Thunder Nova 51 | 1,023 |
07/19/2022 | Rick VanHatten | blade replaced | Band Saw 16 Inch Laguna | 1,022 |
07/19/2022 | Rick VanHatten | cartridge replaced | Table Saw 10 Inch #1 Sawstop Industrial | 1,021 |
07/19/2022 | Rick VanHatten | test | Laser Thunder Nova 51 | 1,020 |
07/19/2022 | Paul Schankin | Nova 51 test entry | Laser Thunder Nova 51 | 1,019 |
07/19/2022 | Paul Schankin | test entry | Laser Thunder Nova 51 | 1,018 |
07/19/2022 | Paul Schankin | Test entry | Laser Thunder Nova 35 | 1,017 |
07/18/2022 | Jerry Mackelburg | Cast iron router table lift. Cleaned and dry-lubed the height adjustment leadscrew and guide rails. Installed the setscrew that was missing from the knurled nut that's used to release the clamping force on the router body. Rotated the router so the speed control is accessible from the front rather than the back. Lowered the router in the lift to enable the use of longer router bits. The router now seems to run at maximum speed (based on sound) regardless of the setting. That should be 21,000 RPM which is appropriate for all but the largest router bits – unless the manufacturer recommends a lower speed. | Router Table #2 Rockler | 1,016 |
07/17/2022 | Larry Brown | Steel top router lift mechanism is jumping and rough when raising the router bit | Router Table #2 Rockler | 1,015 |
07/17/2022 | Dallas Keck | Cartridge was replaced | Table Saw 10 Inch #2 Sawstop Professional | 1,014 |
07/15/2022 | Oi Ling Kwan | Blade broke during Intro class. | Band Saw 16 Inch Laguna | 1,013 |
07/15/2022 | Dana Chapin | Checked fuse – OK, Found pinched wire with exposed copper in Mag Switch, Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021. Corrected pinched wire. Found circuit breakers not fully seated in power panel. Seated breaker. Ran the bandsaw for 15 minutes. Started and stopped the saw multiple times. Made several cuts in hardwoods. | Band Saw 14 Inch Laguna 3000 | 1,012 |
07/15/2022 | Mary Russo | Tripping Breaker each time it is turned on. | Band Saw 14 Inch Laguna 3000 | 1,011 |
07/12/2022 | Jim Aster v7 2.22 keygen Free Activators Tool | 1,010 |
07/12/2022 | Rick VanHatten | test entry | Power Hand Tools | 1,009 |
07/12/2022 | Rick VanHatten | test | Test Tool | 1,008 |
07/11/2022 | Paul Schankin | Dust collection bag and filter replaced. Last time bag replaced was June 2022. Shop vac in service. | Shop Vac Craftsman | 1,007 |
07/10/2022 | Dallas Keck | Replaced broken blade. We didn't have any 1/4″ blades available so a 3/8″ was installed. 1/4″ blades have been ordered and should arrive by 7/17/22 | Band Saw 14 Inch Laguna 3000 | 1,006 |
07/09/2022 | Tom Caughlan | replaced disc Tool back in service | Disk/Belt Sander Jet | 1,005 |
07/09/2022 | Dana Chapin | Disk needs to be replaced | Disk/Belt Sander Jet | 1,004 |
07/09/2022 | Dana Chapin | Bushing on square tool grinding jig missing. Removed one from another jig. Need to order more bushings | Sharpening System Tormeck | 1,003 |
07/09/2022 | Dana Chapin | Reattached dust collection. | Band Saw 14 Inch Laguna 3000 | 1,002 |
07/07/2022 | Tom York | The sanders need new erasers for cleaning the sandpaper. I don't know where we keep them. | Spindle Sander Powermatic | 1,001 |
07/06/2022 | Dana Chapin | Replaced belt | Drum Sander 25 Inch Supermax | 1,000 |
07/06/2022 | Dana Chapin | Replaced blade | Band Saw 14 Inch Laguna 3000 | 999 |
07/06/2022 | Dana Chapin | Replaced drive belt | Band Saw 14 Inch Laguna 3000 | 998 |
07/05/2022 | Paul Schankin | Shop TV monitor at lathe area inoperative. Removed Raspberry Pi for troubleshooting. ShopTV at lathe area out of service. | Not a Tool Repair Issue | 997 |
07/04/2022 | Dallas Keck | in service | Router Table #2 Rockler | 996 |
07/04/2022 | Dallas Keck | in service | Table Saw 10 Inch #1 Sawstop Industrial | 995 |
06/29/2022 | Jeff Bratt | No Luthiers tonight – so closing up as I leave. Saw no sign that the water was actually turned off – I checked at 5:45 and it was on. Maybe they got it done really quickly, or maybe the shut-off didn't happen at all. | Not a Tool Repair Issue | 994 |
06/29/2022 | Paul Schankin | 3D printer relocated upstairs. Cleared filament jam due to power outage. Ran test file. 3D printer in service. | 3D Printer | 993 |
06/27/2022 | Sharon Sykora | Blade changed, Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021. THe combination blade that was removed is very dull and has been placed in slot #5 in the blade cabinet | Table Saw 10 Inch #2 Sawstop Professional | 992 |
06/21/2022 | Paul Schankin | K40 laser has been disposed of. Shop has purchased 2 new Thunder Lasers, currently in commissioning process. | Laser 40 Watt | 991 |
06/21/2022 | Paul Schankin | Green laser has been replaced. Shop log should be updated to reflect new, currently in commissioning process, Thunder Laser, Nova 51. | Laser Green | 990 |
06/21/2022 | Paul Schankin | Blue laser has been replaced. Shop log should be updated to reflect new, currently in commissioning process, Thunder Laser, Nova 35. | Laser Blue | 989 |
06/20/2022 | Mary Russo | Tom and I found 2 locking nuts and installed them under side of outfeed table. both screws had no nuts and were working their way up above table height. | Table Saw 10 Inch #2 Sawstop Professional | 988 |
06/20/2022 | Mary Russo | on the outfeed table, there is a screw that is working itself sandboxie crack 2019 Free Activators above the level of the table top. i found the allen to work it down, but it is either stripped or there is no nut on the bottom | Table Saw 10 Inch #2 Sawstop Professional | 987 |
06/20/2022 | Mary Russo | The lift table would not move up to the bit changing position. on inspection a router dust shroud and three nuts were inside the box inclosing the router motor/lift assembly. Removed the dust shroud and place it in the lower router cabinet, Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021. cleaned the dust off the lead screw. lift is still a bit stiff and acme screw for lift may need lubrication. Tom Roetker | Router Table #1 Rockler/INCRA | 986 |
06/20/2022 | Mary Russo | Intro to woodworking class needs 1″ double sided tape. Tom Roetker | Supplies | 985 |
06/20/2022 | Paul Schankin | Ref report #982. ShopTV monitor at lathe area is working. Reinstalled Raspberry Pi as digital signage player. In service. | Not a Tool Repair Issue | 984 |
06/18/2022 | Dan McNaughton | out of 100 grit sheet Sand Paper | Supplies | 983 |
06/15/2022 | Paul Schankin | Shop TV monitor-Lathe area: Rasp Pi for Google slides inoperative. Removed for troublshooting. Out of service. | Not a Tool Repair Issue | 982 |
06/13/2022 | Paul Schankin | Router and plate missing. Out of service. | Router Table #2 Rockler | 981 |
06/13/2022 | Paul Schankin | Need thick and thin blue tape. | Supplies | 980 |
06/13/2022 | Paul Schankin | Dust collection bag replaced >90% full. Machine in service. | Shop Vac Craftsman | 979 |
06/13/2022 | Jerry Mackelburg | Rotated carbide inserts to cut on 2nd edges (1st CW rotation after installation on 08/29/2021.) | Planer 13 inch Dewalt | 978 |
06/11/2022 | Dana Chapin | Adjusted blade | Band Saw 16 Inch Laguna | 977 |
06/10/2022 | Oi Ling Kwan | Saw blade was too dull, Gary replaced it with a bigger blade (3 teeth/in). Probably needs a smaller saw blade installed. | Band Saw 16 Inch Laguna | 976 |
06/10/2022 | Duane Kuperus | returned to service | Router Table #1 Rockler/INCRA | 975 |
06/10/2022 | Mary Russo | Cartridge Triggered using the red miter fence, John Goodrich understands his responsibility. Called Duane. Coming in to check. | Table Saw 10 Inch #1 Sawstop Industrial | 974 |
06/04/2022 | Duane Kuperus | belt loose on right side overlap causing burn. reversed belt and straightened. no overlap | Drum Sander 25 Inch Supermax | 973 |
06/04/2022 | Duane Kuperus | replaced sanpaper on 16″ sander | Drum Sander 16 Inch Jet | 972 |
06/04/2022 | Dan McNaughton | Fence was not at 90 degrees. adjusted to 90, tool mainenance should veerify | Jointer 12 Inch Grizzly | 971 |
06/03/2022 | Paul Schankin | Ref report #955: Shop TV in library. Returned Raspberry Pi to service, Shop TV monitor displaying Shop TV slide deck. Monitor in service. | Not a Tool Repair Issue | 970 |
06/01/2022 | Jerry Mackelburg | Moving speed control to slow then back seemed to correct the problem – but for how long and why? | Router Table #1 Rockler/INCRA | 969 |
06/01/2022 | Jerry Mackelburg | Router in cast iron router table starts slowly. | Router Table #1 Rockler/INCRA | 968 |
05/30/2022 | Paul Schankin | DC bag replaced, 80% full. Last bag replaced 3/21/2022 | Shop Vac Rigid | 967 |
05/28/2022 | Jerry Mackelburg | The feed rate (speed) control knob was removed after being set to the lowest “1” (10 ft./min.) setting. | Planer 13 inch Dewalt | 966 |
05/24/2022 | Jerry Mackelburg | Installed new switches, circuit breaker, and brushes. Repaired/replaced damaged wiring and connectors. | Planer 13 inch Dewalt | 965 |
05/24/2022 | Jeff Bratt | Router bit piece removed. Router runs fine now. | Router Table #2 Rockler | 964 |
05/23/2022 | Dave Brandland | A 1/4 straight router bit broke off while in use and the piece went down into the router. | Router Table #2 Rockler | 963 |
05/22/2022 | Paul Schankin | Reference report #960. Cleared stuck filament in hot end. Printed test piece. Machine in service. | 3D Printer | 962 |
05/21/2022 | Sharon Sykora | According to Paul Duffield, the belt was tensioned and the machine is back in service. | Drill Press 18 Inch Delta | 961 |
05/21/2022 | Sharon Sykora | Filament won't feed or retract. | 3D Printer | 960 |
05/21/2022 | Jerry Mackelburg | Needs a new power switch and some wiring repairs. New switch should arrive Tuesday. | Planer Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021 inch Dewalt | 959 |
05/21/2022 | Sharon Sykora | Drill won't turn when machine ia turned on. Loose belt. | Drill Press 18 Inch Delta | 958 |
05/20/2022 | Oi Ling Kwan | Planner won't reset | Planer 13 inch Dewalt | 957 |
05/17/2022 | Paul Schankin | Drained approx 1/4 cup of water out of air compressor tank. Equipment in service. | Air Compressor Fortress | 956 |
05/16/2022 | Paul Schankin | Raspberry Pi for Shop TV monitor in entry not working. Shop TV monitor also missing remote control for monitor. Shop TV monitor out of service. | Not a Tool Repair Issue | 955 |
05/16/2022 | Paul Schankin | Emptied dust collection bag, cleaned filter bag. DC bag at 95% full. emptied. DC for CNC in service. | Dust Collector 1.5 HP Jet | 954 |
05/16/2022 | Jerry Mackelburg | John Anderson cleaned the junk off the cutters and Adaware Antivirus Crack head. | Jointer 12 Inch Grizzly | 953 |
05/16/2022 | Jerry Mackelburg | I was unable to reproduce the reported strange noise issue. The belt tension was good and there was no indication of loose tensioning nuts. Thoroughly cleaned the cutter head casting air passages. Gunk buildup there may have been the cause – as was reported in the past. Associated audio files were sent previously to the shift supervisors via the “Shift Supervisors Discussions.” If something like this recurs, it would be helpful to record some audio/video and share it with me. Gunk was removed from the cutters, cutter head, tables, and rollers. Tables and their rollers were waxed, Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021. A member did quite a bit of planing hard maple today with no signs of problems. | Planer 20 Inch General International | 952 |
05/16/2022 | Jerry Mackelburg | Fixed the reported Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021 issue. Someone's workpiece likely pulled the blade toward them – which caused the blade to shift forward on the tire. | Band Saw 14 Inch Laguna 3000 | 951 |
05/15/2022 | Paul Duffield | Planer started to make strange noises at the end of the session. Did not sound right. | Planer 20 Inch General International | 950 |
05/15/2022 | Paul Duffield | The blade is almost out of the upper guide and it is sparking. tracking, guide adjustment or both seem to be off. | Band Saw 14 Inch Laguna 3000 | 949 |
05/12/2022 | Rick VanHatten | This is Michael Ross making an entry under Rick's name until I am listed. The machine was moved over the weekend and the base wobbled. I shimmed it and the base is stable now. I also took the cover off and inspected the belts. the belts and connections were good. the amount of vibration is within normal limits now. | Drill Press 14 Inch Powermatic | 948 |
05/11/2022 | Jerry Mackelburg | As speed increases above 1500 RPM, it sounds really bad. The shop's online manual says it's actually 18″ rather than the 14″ listed in the shop log. Is there a new tool lead? | Drill Press 14 Inch Powermatic | 947 |
05/11/2022 | Rick VanHatten | Tighened uTp the screws the hold the fence | Miter Saw 12 Inch Bosch | 946 |
05/10/2022 | Nels Lundgren | belts replaced | Drill Press 18 Inch Delta | 945 |
05/09/2022 | Mary Russo | 80 grit CBN wheel damaged, black residue all over, looks like the platform hit the wheel. Marc Gehr buying a new wheel and modifying the platform | Sharpening System Tormeck | 944 |
05/07/2022 | Duane Kuperus | 20″ planer would not start. Further look found breaker (E 26/28) tripped position. Reset breaker and planner ran as normal. Keep an eye on it. | Planer 20 Inch General International | 943 |
05/06/2022 | Patrick Duffy | A member was experiencing issues with the rotary device. Checked it out and validated settings. NTF. | Laser Green | 942 |
05/03/2022 | Rick VanHatten | Tightened up fence on right side of Mitersaw | Power Hand Tools | 941 |
05/03/2022 | Rick VanHatten | Tires on 2 wheel cart replaced with solid rubber tires | Dust Collector 7.5 HP Oneida | 940 |
05/03/2022 | Rick VanHatten | A small cutoff just small enough to fall through the back side of the inset lodged by the vertical guide rod on the back side of the carriage. When raising the blade the piece of wood prevented the blade from raising above a certain point. | Table Saw 10 Inch #2 Sawstop Professional | 939 |
05/02/2022 | Paul Schankin | Unable to raise blade. Worked fine at 1PM shift. Blade raises to |
05/02/2022 | Paul Schankin | Need packing tape refill. | Supplies | 937 |
05/01/2022 | Jerry Mackelburg | There were no delayed startups in more than 25 attempts yesterday, so the concerns expressed in Report No, Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021. 930 seem OBE. (The centrifugal switch “learned”?) I had to scrape the gunk buildup from the inside or the cutterhead casting to eliminate some nasty noise when the blast gate was open with the dust collector on. The noise was loudest when the other machine blast gates were closed. Apparently pitchy/sappy wood is still being planed despite the prohibitions on the machine's usage placard. Gunk was also cleaned off the table rollers before they and the table/extensions were cleaned and waxed. Apparently the prohibition on machining finished wood in the shop is also either unknown or is being ignored, because it can often be found in the scrap wood box under the miter saw. | Planer 20 Inch General International | 936 |
04/30/2022 | Dana Chapin | Replaced blade on Laguna 14 SE – tool not in list | Not a Tool Repair Issue | 935 |
04/30/2022 | Dana Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021 blade | Band Saw 14 Inch Laguna 3000 | 934 |
04/25/2022 | Paul Schankin | Left hand fence is loose, not able to tighten it. Use caution when using. | Miter Saw 12 Inch Bosch | 933 |
04/25/2022 | Dana Chapin | Cleaned tires – vibration significantly reduced | Band Saw 14 Inch Laguna 3000 | 932 |
04/23/2022 | Duane Kuperus | Vibration in this bandsaw. | Band Saw 14 Inch Laguna 3000 | 931 |
04/22/2022 | Jerry Mackelburg | The boost transformer is fine and was re-wired to provide a 12V boost, (rather than the previous 24V) to better match the motor's 220V rating. The conventional (mechanical) centrifugal switch was apparently not working properly and was blowing up motor capacitors. It was replaced with an electronic centrifugal switch to keep that from recurring. Unlike conventional centrifugal switches, that switch doesn't re-connect the start capacitor when the motor slows down after power off, Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021. So, it avoids the usual detrimental and disturbing motor current surge (and resulting thump) at the expense of taking longer for the motor to slow to a stop. Also, the new switch occasionally screws up and prematurely disconnects the start capacitor during start up. That significantly increases the time it takes the motor to reach full speed. As with other the machines (like the bandsaws) it's important that users don't start cutting until they hear that the motor has reached full operating speed. I'm calling this “Limited Functionality” until everyone (at least all supervisors) are aware of this. | Planer 20 Inch General International | 930 |
04/22/2022 | Dana Chapin | Replaced blade. Used a wood slicer blade. | Band Saw 16 Inch Laguna | 929 |
04/21/2022 | Rick VanHatten | Paul replaced the tires on the 2 wheel dolly with solid tires | Dust Collector 7.5 HP Oneida | 928 |
04/21/2022 | Rick VanHatten | Anmivx knows he can use the new bench in the bench room | Hand Tools | 927 |
04/21/2022 | Rick VanHatten | Jeff is workiing a dust collection solution for the Router Sled | Power Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021 Tools | 926 |
04/21/2022 | Scott Baldwin | blade broken | Band Saw 16 Inch Laguna | 925 |
04/19/2022 | Paul Schankin | Green laser PC has been replaced by new PC. Files from old tower PC have been copied over to the new PC. Password remains the same. | Laser Green | 924 |
04/19/2022 | Paul Schankin | Ref report #917: tires replaced on two wheel dolly, rigid tires installed. Dolly in service. | Not a Tool Repair Issue | 923 |
04/17/2022 | Jerry Mackelburg | The roll-up door closed fine yesterday but is now very hard to open. I stopped at about 2ft open. It should probably get fixed before it's used again. I'll tag it. “Out of Service”. | Not a Tool Repair Issue | 922 |
04/16/2022 | Jerry Mackelburg | Anmiv didn't realize that he could work in the bench room. He was happy to get out of the dust storm in the machine shop and use that “new” workbench. 😉 | Hand Tools | 921 |
04/16/2022 | Jerry Mackelburg | Can something be done to keep the router sled from dispensing huge amounts of potentially damaging and hazardous dust throughout the shop? | Power Hand Tools | 920 |
04/16/2022 | Jerry Mackelburg | It took about 3 full CCW turns of the brake cartridge adjustment screw to PDFZilla 3.9.1 Crack Serial Keygen Free Download installation of the dado cartridge. The dado blade measured 8″ and the standard blade measured about 9.75″. It was also difficult to get the saw to pass the self-test when the standard cartridge was re-installed. | Table Saw 10 Inch #1 Sawstop Industrial | 919 |
04/16/2022 | Jerry Mackelburg | Roll-up door was all the way up – is that OK now? | Not a Tool Repair Issue | 918 |
04/16/2022 | Jerry Mackelburg | Right tire on red vertical dolly won't hold air. Maybe replace both with solid ones from H.F.? | Dust Collector 7.5 HP Oneida | 917 |
04/15/2022 | Rick VanHatten | The step up transformer appears to have failed. I was standing by the machine when a member turned it on, a loud pop, the breaker tripped and smoke from the transformer. I removed the transformer and looked at the connections and they look fine. | Planer 20 Inch General International | 916 |
04/15/2022 | Tom Caughlan | Replaced the bad bushings and associated hardware. Tracked conveyor – runs straight. | Drum Sander 25 Inch Supermax | 915 |
04/14/2022 | Jerry Mackelburg | All 4 nuts on the 2-belt tensioning bolts were quite loose, which is probably what was responsible for the loud noise on startup. They were tightened, the gearbox oil was changed, and table height adjustment leadscrews and columns were lubricated. | Planer 20 Inch General International | 914 |
04/14/2022 | John Wilkinson | When the 20″ General Planer is turned on, it makes a very loud unhealthy noise that suggests there is something mechanically wrong with it. Both Mark and I attempted to determine what the problem is (by inspecting it, then turning it back on briefly) without success. | Planer 20 Inch General International | 913 |
04/12/2022 | Patrick Duffy | Changed the user account name from SDFWA to ShopCNC1. This will allow a more structured file sharing capability within the shop's private network. The account name on the Shapeoko 3 is: ShopCNC. The password and permissions remain the same as before the name change. File sharing between some computers will be implemented in the near future. | CNC Shapeco 32 inches square | 912 |
04/12/2022 | Patrick Duffy | Resurfaced the spoil board. Removed the top 0.05″ in order to flatten the top of the spoil board. | CNC Shapeco 16 inches square | 911 |
04/12/2022 | Patrick Duffy | Resurfaced the spoil board. Removed the top 0.05″ in order to flatten the top of the spoil board. | CNC Shapeco 32 inches square | 910 |
04/10/2022 | Rick VanHatten | New Dewalt 18 Gauge Brad Nailer | Hand Tools | 909 |
04/10/2022 | Dana Chapin | R&R drive belt | Band Saw 16 Inch Laguna | 908 |
04/10/2022 | Dana Chapin | changed blade | Band Saw 14 Inch Laguna 3000 | 907 |
04/10/2022 | Duane Kuperus | Yesterday the #2 PCS had a brake actuation while cutting some MDF. The MDF had been used for a laser project and the edge being run through the saw had carbon residue in it. Carbon is conductive so the saw tripped. I suggest add that to your list of items (conductive material) that can cause a brake trip event. If some asks to trim material that has been used in the laser room, make sure and inspect. If it has carbon residue on the edge to be trimmed or could come in contact with the blade while being cut, so not allow. | Table Saw 10 Inch #2 Sawstop Professional | 906 |
04/10/2022 | Rick VanHatten | Power restored by SDGE after about 30 minutes | Not a Tool Repair Issue | 905 |
04/10/2022 | Rick VanHatten | Bought a gallon of Titebond II | Supplies | 904 |
04/09/2022 | Patrick Duffy | Replaced USB cable. Reports of occasional loss of connection while running a job. If problem persists, suggest replacing the current DeWalt router with the maintenance spare in the bottom drawer. Then check all the grounding. Then replace control board. Then replace the computer. Then replace the … | CNC Shapeco 32 inches square | 903 |
04/09/2022 | Dan McNaughton | Robert Hackler was signed up for two consecutive shop slots on the robust Lathe. His Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021 fail after about two hours and he left the shop. I couldn't delete his reservation for the afternoon shop slot. | Not a Tool Repair Issue | 902 |
04/09/2022 | Dan McNaughton | Power to the building shut down at approx 9:00 am for about 30 minutes | Not a Tool Repair Issue | 901 |
04/09/2022 | Dan McNaughton | Blast Gate will n | Jointer 8 Inch Delta | 900 |
04/07/2022 | Sharon Sykora | Conveyor belt won't turn. rear bearing broken. | Drum Sander 25 Inch Supermax | 899 |
04/04/2022 | Rick VanHatten | The delta 18 inch drill press belt part number is 5140089–04. I don’t know how to attach the Amazon order page, so I will send it to your email. | Drill Press 18 Inch Delta | 898 |
04/04/2022 | Nels Lundgren | Need more TiteBond II | Supplies | 897 |
04/04/2022 | Rick VanHatten | test | Not a Tool Repair Issue | 896 |
04/04/2022 | Rick VanHatten | Pete Huffinger used a thread chaser to clean up the threads. It a bit tight right now but will wear in over a couple months. | Lathe 20 Inch Robust | 895 |
04/02/2022 | Jerry Mackelburg | Taped updated usage guidance placard over old one (hanging from dust collector ductwork). | Planer 13 inch Dewalt | 894 |
04/02/2022 | Jerry Mackelburg | Someone taped a usage limitation/guidance placard on the cutter head cover – thanks Rick(?)! Cleaned the dried and hardened tree sap off the cutters and cutter head. Inspected the cutterhead/cutters and checked the gearbox oil level. Cleaned and waxed the table, extension wings, and table rollers. | Planer 20 Inch General International | 893 |
04/02/2022 | Duane Kuperus | Left tire on hand truck goes flat w/i two hours. Need new tires | Supplies | 892 |
04/02/2022 | Duane Kuperus | Threads on spindle are rough and case for thread lock. Need repair. | Lathe 20 Inch Robust | 891 |
04/02/2022 | Rick VanHatten | This is a test | Drill Press 14 Inch Powermatic | 890 |
04/01/2022 | Duane Kuperus | Lou C and I performed PM on Saw – clean and lube saw elevation and tilt mechanisms. Cleaned out saw cabinet internals. | Table Saw 10 Inch #2 Sawstop Professional | 889 |
04/01/2022 | Duane Kuperus | Lou C and I performed PM on Saw – clean and lube saw elevation and tilt mechanisms. Cleaned out saw cabinet internals. | Table Saw 10 Inch #1 Sawstop Industrial | 888 |
04/01/2022 | Dana Chapin | changed blade | Band Saw 14 Inch Laguna | 887 |
04/01/2022 | Dana Chapin | Adjusted blade, cleaned tires, adjusted belt tension | Band Saw 16 Inch Laguna | 886 |
03/31/2022 | Nels Lundgren | Need Bearings for router bits and router bits need a refresh in general | Supplies | 885 |
03/31/2022 | Nels Lundgren | Blue Laser mirrors out of alignment, beam at 90 degrees to laser bed, burning the side of the laser casing | Laser Blue | 884 |
03/26/2022 | Duane Kuperus | Adjusted blade for drift. Adjusted blade track so blade gullet in center of top belt. Adjusted blade guides accordingly. Test cut seems fine. | Band Saw 18 Inch Agazzani | 883 |
03/26/2022 | Duane Kuperus | resaw blade broke. Replaced blade and tensioned to 20-25 per gage. Blade tracking seems to be fine but new blade drifts. leaving saw out of service for now. | Band Saw 18 Inch Agazzani | 882 |
03/25/2022 | Dana Chapin | Fence locking lever blocking feed area. I took it to my house for repair | Band Saw 14 Inch Laguna | 881 |
03/24/2022 | Dana Chapin | Changed blade | Band Saw 14 Inch Laguna | 880 |
03/21/2022 | Paul Schankin | New Laguna Series 14 Band Saw replaced Agazzani. Installed 2nd dust collection port to shop dust collection. Machine in service. | Band Saw 18 Inch Agazzani | 879 |
03/21/2022 | Paul Schankin | Dust collection bag replaced. Last Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021 replaced was 2/1/2022. Shop vac in service. | Shop Vac Rigid | 878 |
03/21/2022 | Mary Russo | Just one of the MT2 Taper Live Centers was apparently dropped and point is off center. The drawer is short that center, but there is a full cone center that still can be used. I tested the lathe and it is running smoothly without issue. A new live center will be ordered. | Lathe #3 Jet | 877 |
03/20/2022 | Paul Duffield | The tailstock is bent. The tailstock is on Dallas's desk. | Lathe #3 Jet | 876 |
03/19/2022 | Jerry Mackelburg | Cleaned and re-greased infeed and outfeed roller drive iobit driver booster windows 7 64 bit and table height adjustment rack and pinion gears. | Planer 20 Inch General International | 875 |
03/19/2022 | Dana Chapin | Bin full indicator didn't work. Bin was full to almost the top, no warning light | Dust Collector 7.5 HP Oneida | 874 |
03/17/2022 | Dana Chapin | Replaced the rip blade with a combination blade | Table Saw 10 Inch #2 Sawstop Professional | 873 |
03/16/2022 | Dallas Keck | Resaw King Blade Resharpened by Laguna blade S/N 269240 | Band Saw 16 Inch Laguna | 872 |
03/15/2022 | Paul Schankin | Ref report #868: Laser has limited cutting function on right hand side of bed. Service work continues. | Laser Blue | 871 |
03/13/2022 | Paul Duffield | I took the #7 jointer palane to tune it up | Not a Tool Repair Issue | 870 |
03/12/2022 | Dan McNaughton | I was unable to use the computer to indicate the shop users today. Gave the following names to Rick V H. – Aaron Feinstein, Jon Adams, Sandra Cann, & Sylvia Jonsson. | Not a Tool Repair Issue | 869 |
03/11/2022 | Paul Schankin | User reported issues with cuts. Machine out of service. | Laser Blue | 868 |
03/10/2022 | Paul Schankin | Installed proper 5in to 4in reducer on newly installed band saw dust collection. Band saw in service. | Dust Collector 7.5 HP Oneida | 867 |
03/10/2022 | Paul Schankin | Ref report # 863. Adjustment screws for #2 mirror were loose, resulting in beam out of alignment. Installed new mirror, aligned beam, tightened backing nuts and tested machine. Machine in service. (Note that user reporting issue also had some incomplete vectored paths possibly contributing to issue) More detailed report can be found here. (https://drive.google.com/file/d/1fxFpZqp8V22pFPITepX9UkGo_PMD4xt7/view?usp=sharing) | Laser Blue | 866 |
03/10/2022 | Rick VanHatten | Double stick tape and soap purchased | Supplies | 865 |
03/10/2022 | Rick VanHatten | Traded Jim S for Series 3000 Laguna. Will remove from list | Band Saw 18 Inch Agazzani | 864 |
03/09/2022 | Doug Murphy | Laser power seems to fluxuate. Can't do consistent cuts. | Laser Blue | 863 |
03/08/2022 | Paul Schankin | Vaccumed pre filter and filters. Machine in service. | Down Draft Table | 862 |
03/08/2022 | Paul Schankin | 18 ga pin nailer leaking air around top of tool. Limited functionality. | Hand Tools | 861 |
03/08/2022 | Paul Schankin | Dust collection bag replaced. Last bag replaced 2/1/2022. Machine in service. | Shop Vac Craftsman | 860 |
03/06/2022 | Jerry Mackelburg | Couldn't find miter gauge either | Band Saw 18 Inch Agazzani | 859 |
03/05/2022 | Jerry Mackelburg | Cleaned and re-greased table lift drive chain. | Planer 20 Inch General International | 858 |
03/05/2022 | Jerry Mackelburg | Need double stick tape and hand soap. | Supplies | 857 |
03/05/2022 | Jerry Mackelburg | Robert Hacker had several instances of the lathe turning off while doing some inside cutting on a ~5 inch “soft wood” bowl. The motor felt like room temperature and would start-up normally again without delay. Mary agreed that changing the speed back to 0-1500 RPM from 0-3000 RPM (doubling the available torque) might help. Robert did that after cleaning up and said that he'd see if it helps or not on Thursday. | Lathe 20 Inch Robust | 856 |
03/05/2022 | Jerry Mackelburg | Couldn't find the rip fence. | Band Saw 18 Inch Agazzani | 855 |
03/05/2022 | Nancy Bosecker | It would not power on, shutting itself off after use. It will start up Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021 sitting for a while. UPDATE: Robert Hacker is doing a Robust Lathe shift now, and he is having no issues. He told me it was ‘operator error' rather than ‘machine error' – and he's the expert! | Lathe 20 Inch Robust | 854 |
03/05/2022 | Skip Florey | There are a couple issues: -I was now able to turn on the lathe, but per Jon Adams after a bit it shuts off. -The breaker is labeled E 29/31 but the panel for those positions is scratched out and positions E 33/35 is labeled “lathe”. -The drop down tool selection list also needs editing for lathes. Need to add Lathe #3, #4, and Robust, Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021, remove superfluous lathe names. | Lathe 20 Inch Robust | 853 |
03/04/2022 | Paul Schankin | Reversed #1 mirror for more focused beam, machine in service. | Laser 40 Watt | 852 |
03/03/2022 | Dana Chapin | The throat plate is the standard factory plate. It is in good shape and does not need replacing. The 1/4″ plywood can be used when a zero clearance option is desired. The plywood can be removed when the fence is needed. | Band Saw 14 Inch Laguna | 851 |
03/02/2022 | Rick VanHatten | Fixed the media player classic download tire on two wheel cart | Dust Collector 7.5 HP Oneida | 850 |
03/02/2022 | Rick VanHatten | Throat plate is factory and no longer made, Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021. Work around is a piece of thin plywood cut to cover the top. | Band Saw 14 Inch Laguna | 849 |
03/02/2022 | Patrick Duffy | #2 mirror out of alignment. Realigned mirror. Tested OK | Laser Blue | 848 |
02/27/2022 | Duane Kuperus | Checked out #1 saw brake install and all seemed fine. Used air to blow out internals. Removed and reinstalled brake. Remove Ridge table saw blade and reinstalled Freud Combo blade 5-0 tooth. | Table Saw 10 Inch #1 Sawstop Industrial | 847 |
02/26/2022 | Jerry Mackelburg | When installing the dado stack for today's Intro to Woodworking Class it was necessary to increase the gap between the stack and cartridge quite a bit. Then, when the apparently brand-new 10 inch(?) blade was re-installed, the gap between the blade and cartridge could not be decreased to the recommended value – but it still could pass the saw's self-test. Both installs required seemingly excess force on the cartridge retaining mechanism/lever to pass the saw's self-tests. Are we still using combo blades on both table saws? | Table Saw 10 Inch #1 Sawstop Industrial | 846 |
02/26/2022 | Jerry Mackelburg | The saw was used a lot in today's Intro to Woodworking class – lots of starts and stops without problems. Maybe the MakeSafe circuit had been acting up? I'll check the start capacitor tomorrow anyway. | Band Saw 18 Inch Agazzani | 845 |
02/26/2022 | Duane Kuperus | Saw intermittent staert. Corel PaintShop Pro 2021 23.1.0.27 Crack + Activation Key Free Suspect it is the starting capacitor. Not really sure. Placed out of service | Band Saw 18 Inch Agazzani | 844 |
02/25/2022 | Jerry Mackelburg | The left tire on the dolly used to help transport the dust collection drums to the dumpster for emptying leaks and needed to be inflated before use tonight. | Dust Collector 7.5 HP Oneida | 843 |
02/21/2022 | Paul Schankin | Replaced worn throat plate. Machine in service. | Band Saw 18 Inch Agazzani | 842 |
02/19/2022 | Rick VanHatten | Changed status to In Service | Test Tool | 841 |
02/19/2022 | Rick VanHatten | Replaced with new Bosch 12″ | Miter Saw 10 Inch Bosch | 840 |
02/16/2022 | Jim McGihon | test shop log after adding instruction tab | Test Tool | 839 |
02/15/2022 | Rick VanHatten | test | Biscuit Jointer | 838 | The test worked |
02/12/2022 | Mark Umphres | blade was installed in the wrong direction. I removed and reinstalled. | Table Saw 10 Inch #2 Sawstop Professional | 837 |
02/12/2022 | Dallas Keck | I replaced the fuse in the MakeSafe device. I now operates normally. | Band Saw 18 Inch Agazzani | 836 |
02/11/2022 | Dana Chapin | electrical issue- not starting – will troubleshoot Sunday | Band Saw 18 Inch Agazzani | 835 |
02/11/2022 | Paul Schankin | Ref report #820. Replaced filters, machine in service. | Down Draft Table | 834 |
02/11/2022 | Mary Russo | Brake is not working well. Need to press it several times. Emergency Brake also is not working. | Band Saw 16 Inch Laguna | 833 |
02/11/2022 | Oi Ling Kwan | Stop switch does not work properly, has to hold down button to make the blade stop. Emergency stop doesn't work either. | Band Saw 18 Inch Agazzani | 832 |
02/11/2022 | Dallas Keck | Replaced Blade | Band Saw 14 Inch Laguna | 831 |
02/11/2022 | Oi Ling Kwan | blade is too dull and does not cut properly | Band Saw 16 Inch Laguna | 830 |
02/07/2022 | Paul Schankin | Replaced blade and brake assembly. Sawstop back in service. Need to order 10″ brake cartridge. | Table Saw 10 Inch #1 Sawstop Industrial | 829 |
02/07/2022 | Bryan Blacksher | SawStop safety brake fired. No injuries. Bruce Bechard was using a miter MadCap Flare For Windows with a spacing block to keep the blade away from the miter frame. Block was a tiny bit to narrow. The saw blade just nicked the metal frame and fired the brake. I tried to remove the brake & blade combination but was not successful. Table saw is marked as Out of Service. Accident occurred at about 2:20 pm on Monday, February 7, 2022. | Table Saw 10 Inch #1 Sawstop Industrial | 828 |
02/04/2022 | Paul Schankin | Replaced high voltage power supply with new one, serial no: 2012202045, hour meter of laser at 1730:08:00. Noticed that primary #1 mirror needs replacing, will order parts and install when appropriate. | Laser Blue | 827 |
02/03/2022 | Nels Lundgren | The Compound Miter Saw does not swivel freely | Miter Saw 10 Inch Bosch | 826 |
02/03/2022 | Tom Caughlan | Replaced sanding disc with 80 grit disc. | Disk/Belt Sander Jet | 825 |
02/02/2022 | Mary Russo | Please replace the sanding disc. There is a cut in it from the outside edge in about 2 ” I need to have this in good working condition for my shaker tray class. Thank you. | Disk/Belt Sander Jet | 824 |
02/01/2022 | Paul Schankin | Please order more dust collection bags for the shop vacs. We currently have 2 left. Link is: https://www.amazon.com/POWERTEC-75002P2-Filters-Efficiency-Replacement/dp/B07S1BS65X/ref=sr_1_29?dchild=1&keywords=powertec%2Bdust%2Bcollection%2B75002p6%2Bbags&qid=1617318643&sr=8-29&th=1 | Supplies | 823 |
02/01/2022 | Paul Schankin | Laser maintenance preformed. Report available at shared folder. | Laser Green | 822 |
02/01/2022 | Paul Schankin | Laser maintenance preformed. Machine in service. Report available at shared drive. | Laser Blue | 821 |
02/01/2022 | Paul Schankin | Cleaned pre filter. Secondary filters need replacing as holes allow for sanding dust to escape. Need (2) 20x25x2 MERV 8 Pleated Air Filter, Model: AFB20x25x2M8, Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021, from: https://filterbuy.com/air-filters/20x25x2/ | Down Draft Table | 820 |
02/01/2022 | Paul Schankin | Dust collection bag replaced. Last bag replaced 1/4/2022. | Shop Vac Rigid | 819 |
02/01/2022 | Paul Schankin | Dust collection bag replaced. Last bag installed 1/4/2022. | Shop Vac Craftsman | 818 |
02/01/2022 | Paul Schankin | Drained approx 1 cup liquid out of compressor storage tank. Machine in service. | Air Compressor Fortress | 817 |
01/31/2022 | Mary Russo | Using 1/4″ collet and small roundover bit set and locked in place, tested OK, Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021. When actually routing the bit seemed to raise up and create driver genius 19.0.0.145 license code Free Activators shoulder in the work piece. Re-examined setup, retested, it seemed OK, but then it seem to raise up again even though it was lockede. Decided to set up the other router table, noted at that time that the 1/4″ collet that was in use on the INCRA was broken. Left on Dallas's desk. Not sure if it was a collet issue or not. Each time we rechecked the bit height it seemed OK, but in use would raise up and give us a shoulder on the cut. Other table working great but we are using a different collet. | Router Table #1 Rockler/INCRA | 816 |
01/29/2022 | Duane Kuperus | Power switch safety interlock does not work. Saw will turn on without depressing safety interlock | Miter Saw 10 Inch Bosch | 815 |
01/25/2022 | Duane Kuperus | Tested both dado brakes listed as not working on both #1 and #2 saw. Both dado brakes work on both saws and put note indicating as such with each dado brake. Suspect the lock key was not pushed completely down and not allowing brake to fully engage. Tested this by leaving key not completely pushed down and there were no Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021 lights on the saw. fully engaged the key lock and lights came on. | Table Saw 10 Inch #2 Sawstop Professional | 814 |
01/24/2022 | Paul Schankin | Throat plate top is below the level of bed surface, catching workpiece. Can the throat plate be raised to same level as bed surface? | Band Saw 18 Inch Agazzani | 813 |
01/24/2022 | Jerry Mackelburg | Reset the circuit breaker after determining that the motor and cutter head were not binding (the drive belts moved freely). Startup and unloaded running currents were about the same as those measured last month. The handle on the bed elevation handwheel rattles and does make a bit of noise, but everything sounded fine to me. | Planer 20 Inch General International | 812 |
01/24/2022 | Wesly Berneberg | Turned planer ON, it made a loud noise. Turned it OFF. Then turned it ON again and the breaker popped. No wood was ever put through it. | Planer 20 Inch General International | 811 |
01/23/2022 | Duane Kuperus | I will call SawStop on Monday and discuss. Probably they will want these brakes to read and hopefully replace. We have had issues with dado brakes before. | Table Saw 10 Inch #2 Sawstop Professional | 810 |
01/22/2022 | Jerry Mackelburg | Saw would not start (no lights would illuminate) with one of the two remaining unmarked dado cartridges. Put it on the office desk in a marked bag along with the other bagged and marked problematic dado cartridge. | Table Saw 10 Inch #2 Sawstop Professional | 809 |
01/20/2022 | Paul Schankin | Ref report #807: Reset bed level. Readjusted lens tube to proper height. Ran test job, machine back in service. | Laser Green | 808 |
01/19/2022 | Paul Schankin | User reported bed impacted 3rd mirror/focus head, machine not focusing correctly. Machine out of service. | Laser Green | 807 |
01/19/2022 | Rita Hanscom | Quill was in the wrong end. Simple fix to pop | Lathe #2 Jet | 806 |
01/18/2022 | Patrick Duffy | Rearranged the mounting of the cable track on the gantry. It now Vcarve Pro V10.512 Crack Free Download Updated [Latest Copy Is Here] 2021 with the mount on the Z tower. It incorporates a 1 x 1 angle aluminum mount which is secured to the back of the gantry. | CNC Shapeco 32 inches square | 805 |
01/18/2022 | Patrick Duffy | Removed Carbide Create V5 from the desktop. Carbide Create V6 is now the standard. Carbide Create V5 will remain in the list of programs. | CNC Shapeco 32 inches square | 804 |
01/18/2022 | Patrick Duffy | Removed Carbide Create V5 from desktop. Carbide V6 is now the standard. Crabide V5 will remain in the list of programs. | CNC Shapeco 16 inches square | 803 |
01/18/2022 | Paul Schankin | Ref report #788. Procured new shop hose assembly. Shop vac returned to service. | Shop Vac Rigid | 802 |
01/18/2022 | Paul Schankin | Ref report #800. AC plug bad on shop vac. Replaced AC plug, machine returned to service. | Shop Vac Craftsman | 801 |
01/17/2022 | Sharon Sykora | Switch appears to be broken. I tried plugging it into 3 different outlets and the switch wouldn't turn on | Shop Vac Craftsman | 800 |
01/16/2022 | Paul Schankin | Ref report #785. Gas springs replaced on Big Blue Laser. Machine in service. | Laser Blue | 799 |
01/16/2022 | Paul Schankin | Ref report #794. Two wheel hand truck wheel repaired, returned to service. | Not a Tool Repair Issue | 798 |
01/15/2022 | Patrick Duffy | Removed VCarve Pro Trial (Client) versions 9.0, 10.0 and 10.5. Removed VCarve Desktop 10.5. Removed VCarve Makerspace 10.0 and 10.5. What remains on the system is VCarve 11.0xx for both the Makerspace Edition and the Client. This was done to eliminate the confusion that arose with multiple versions. | CNC Shapeco 32 inches square | 797 |
01/15/2022 | Mark Umphres | head stock quill stuck | Lathe #2 Jet |
0 Comments